View MC10133_128961.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Quad Latch
The MC10133 is a high speed, low power, quad latch consisting of four bistable latch circuits with D type inputs and gated Q outputs, allowing direct wiring to a bus. When the clock is high, outputs will follow D inputs. Information is latched on the negative going transition of the clock. The outputs are gated when the output enable (G) is low. All four latches may be clocked at one time with the common clock (CC), or each half may be clocked separately with its clock enable (CE).
MC10133
PD = 310 mW typ/pkg (No Load) tpd = 4.0 ns typ tr, tf = 2.0 ns typ (20%-80%)
L SUFFIX CERAMIC PACKAGE CASE 620-10
P SUFFIX PLASTIC PACKAGE CASE 648-08
LOGIC DIAGRAM
D0 3 Q0 2 Q0
G0 D1 CE
5 7 4
DIP PIN ASSIGNMENT
6 Q1 VCC1 Q0 D0 Q2 11 Q2 CE G0 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VCC2 Q3 D3 CC CE Q2 G1 D2 Q1
CC 13 CE 12 D2 9 G1 10
D3 14
Q3
15 Q3
Q1 D1
TRUTH TABLE
G H L L L C X L H H D X X L H Qn+1 L Qn L H VEE VCC1 = PIN 1 VCC2 = PIN 16 VEE = PIN 8
C = CC + CE
9/96
(c) Motorola, Inc. 1996
3-13
REV 6
MC10133
ELECTRICAL CHARACTERISTICS
Test Limits Pin Pi Under Test 8 3 4 5 13 3 2 2 2 2 2 2 2 2 2[ 2] 2] 2 2 2 2 2 2[ 2] 2] 0.5 -1.060 -1.060 -1.890 -1.890 -1.890 -1.080 -1.080 -1.080 -1.080 -1.080 -1.080 -1.080 -1.080 -1.655 -1.655 -1.655 -1.655 -1.655 -1.655 -0.890 -0.890 -1.675 -1.675 -1.675 -30C Min Max 82 390 425 560 560 0.5 -0.960 -0.960 -1.850 -1.850 -1.850 -0.980 -0.980 -0.980 -0.980 -0.980 -0.980 -0.980 -0.980 -1.630 -1.630 -1.630 -1.630 -1.630 -1.630 -0.810 -0.810 -1.650 -1.650 -1.650 Min +25C Typ Max 75 245 265 350 350 0.3 -0.890 -0.890 -1.825 -1.825 -1.825 -0.910 -0.910 -0.910 -0.910 -0.910 -0.910 -0.910 -0.910 -1.595 -1.595 -1.595 -1.595 -1.595 -1.595 -0.700 -0.700 -1.615 -1.615 -1.615 Min +85C Max 82 245 265 350 350 Unit mAdc Adc
Characteristic Power Supply Drain Current Input Current
Symbol IE IinH
IinL Output Voltage Output Voltage Logic 1 Logic 0 VOH VOL
Adc Vdc Vdc
Threshold Voltage
Logic 1
VOHA
Vdc
Threshold Voltage
Logic 0
VOLA
Vdc
Switching Times Propagation Delay
(50 Load) t3+2+ t4+2+ t5-2+ tsetup thold t2+ t2- 2 2 2 3 3 2 2 1.0 1.0 1.0 2.5 1.5 1.0 1.0 5.6 5.4 3.2 1.0 1.0 1.0 2.5 1.5 1.1 1.1 4.0 4.0 2.0 0.7 0.7 2.0 2.0 5.4 5.4 3.1 1.1 1.2 1.0 2.5 1.5 1.1 1.1 VIHmax VILmin 5.9 6.0 3.4
ns
Rise Time Fall Time
(20 to 80%) (20 to 80%)
3.6 3.6
3.5 3.5
3.8 3.8
[ Output level to be measured after a clock pulse has been applied to the clock input (Pin 4)
] Data input at proper high/low level while clock pulse is high so that device latches ar proper high/low level for test. Levels are measured after
device has latched. * Latch set to zero state before test.
MOTOROLA
3-14
MECL Data DL122 -- Rev 6
MC10133
ELECTRICAL CHARACTERISTICS (continued)
TEST VOLTAGE VALUES (Volts) @ Test Temperature -30C +25C +85C Pin Under Test 8 3 4 5 13 3 2 2 2 2 2 2 2 2 2[ 2] 2] 2 2 2 2 2 2[ 2] 2] 3, 4 3, 13 13 3, 5, 13 4 3, 4 4 3, 4 3 3 3 5 3 3 4 5 13 3 VIHmax -0.890 -0.810 -0.700 VILmin -1.890 -1.850 -1.825 VIHAmin -1.205 -1.105 -1.035 VILAmax -1.500 -1.475 -1.440 VEE -5.2 -5.2 -5.2 (VCC) Gnd 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 +2.0 V 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16 1, 16
TEST VOLTAGE APPLIED TO PINS LISTED BELOW VIHmax VILmin 13 VIHAmin VILAmax VEE 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 -3.2 V 8 8 8 8 8 8 8
Characteristic Power Supply Drain Current Input Current
Symbol IE IinH
IinL Output Voltage Output Voltage Logic 1 Logic 0 VOH VOL
Threshold Voltage
Logic 1
VOHA
4 3 3 3, 4 4 4 3 3 +1.11V Pulse In 3 4 5 3 3 3 3 4 13 5 3
Threshold Voltage
Logic 0
VOLA
13 Pulse Out 2 2 2 2 2 2 2 VIHmax VILmin
Switching Times Propagation Delay
(50 Load) t3+2+ t4+2+ t5-2+ tsetup thold (20 to 80%) (20 to 80%) t2+ t2- 2 2 2 3 3 2 2
4 3*
Rise Time Fall Time
4 4
[ Output level to be measured after a clock pulse has been applied to the clock input (Pin 4)
] Data input at proper high/low level while clock pulse is high so that device latches ar proper high/low level for test. Levels are measured after
device has latched. * Latch set to zero state before test. Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated through a 50-ohm resistor to -2.0 volts. Test procedures are shown for only one gate. The other gates are tested in the same manner.
MECL Data DL122 -- Rev 6
3-15
MOTOROLA
MC10133
OUTLINE DIMENSIONS
L SUFFIX CERAMIC DIP PACKAGE CASE 620-10 ISSUE V
9
-A-
16
-B-
1 8
C
L
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. DIM A B C D E F G H K L M N INCHES MIN MAX 0.750 0.785 0.240 0.295 --- 0.200 0.015 0.020 0.050 BSC 0.055 0.065 0.100 BSC 0.008 0.015 0.125 0.170 0.300 BSC 0_ 15 _ 0.020 0.040 MILLIMETERS MIN MAX 19.05 19.93 6.10 7.49 --- 5.08 0.39 0.50 1.27 BSC 1.40 1.65 2.54 BSC 0.21 0.38 3.18 4.31 7.62 BSC 0_ 15 _ 0.51 1.01
-T-
SEATING PLANE
N E F D G
16 PL
K M J
16 PL
0.25 (0.010)
M
M
TB
S
0.25 (0.010)
TA
S
-A-
16 9
P SUFFIX PLASTIC DIP PACKAGE CASE 648-08 ISSUE R
B
1 8
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01
F S
C
L
-T- H G D
16 PL
SEATING PLANE
K
J TA
M
M
0.25 (0.010)
M
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303-675-2140 or 1-800-441-2447 MfaxTM: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 81-3-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA 3-16
*MC10133/D*
MC10133/D MECL Data DL122 -- Rev 6

▲Up To Search▲

Price & Availability of MC10133

	To Download MC10133 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .